The article below about How to Install a Bathtub is incredibly attention-grabbing. You should investigate it.
Installing a bath tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the job can move speedily; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This post will assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools and also material list should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the faucet in place with the maker offered backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, put the bathtub in the required position. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water as well as check all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow outlet and also the normal outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has actually been made use of a minimum of when as this will certainly settle it right into its last setting.
Planning for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that article post was worth the trouble. I beg you take the time to distribute this entry if you enjoyed it. Thanks a bunch for your time. Kindly come visit our blog back soon.
Detail